REX-F9000 Specifications

---

Input
Number of Inputs	1 or 2 points
Input	RTD : Pt100 (JIS/IEC), JPt100 (JIS) 3 or 4 wire system Influence of input lead resistance : Less than 0.04°C (Less than 10W per wire) Input break action : Up-scale Input short action : Down-scale
Input Range	0.000 to 50.000°C
Sampling Time	0.1 sec
PV Bias	-19.999 to 19.999°C
Digital Filter	0.1 to 100.0 sec (No filter when 0.0 is set)

Performance
Setting Accuracy	a) Temperature : ±0.05°C b) Other setting : Within ±0.1% of setting range
Measuring Accuracy	±0.05°C ( Ambient temperature 23°C ±5°C )
Insulation Resistance	More than 20MW (500V DC) between measured and ground terminals. More than 20MW (500V DC) between power and ground terminals.
Dielectric Strength	1000V AC for one minute between measured and ground terminals. 1500V AC for one minute between power and ground terminals.

Control
Control Method	Brilliant PID control with autotuning Direct/Reverse action (Selectable)
Major Setting Range	Set value : 0.000 to 50.000°C Proportional band : 0.001 to 50.000°C Integral time : 0.1 to 3600.0 sec. (Zero is not settable) Derivative time : 0.1 to 3600.0 sec. (PI action when D=0) Control response : 0 (Slow), 1 (Medium), 2 (Fast) Proportional cycle : 0.1 to 100.0 sec. (Only voltage pulse output)
Control Output	Voltage pulse output : 0/12V DC (Load resistance : More than 600W) Current output : 4 to 20mA DC (Load resistance : Less than 600W) Output resolution : More than 13 bits Output impedance : More than 5MW

Alarms
Temperature Alarm	a) Number of alarms : 2 points / channel b) Type : Deviation High, Low, High/Low, Band Process High, Low Set value High, Low c) Setting range : Deviation and band alarm : -19.999 to 19.999°C (Action is not guaranteed in the case of an alarm setting that is outside of the input range.) Process alarm : 0.000 to 50.000°C d) Alarm differential gap : 0.001 to 50.000°C e) Alarm timer : 0 to 600 sec.
Alarm Output	Relay output, Form A contact 250V AC 1A (resistive load) Energized or de-energized output

Communications
Communication Method	RS-485 (2-wire)
Communication Speed	1200, 2400, 4800, 9600, 19200 BPS
Bit Format	Start bit : 1 Data bit : 7 or 8 Parity bit : Without, Odd or Even Stop bit : 1 or 2
Communication Code	ASCII (JIS) 7-bit code
Maximum Connection	31 (Address can be set from 0 to 99.)

Contact Input
Number of Inputs	1 point
Type	RUN/STOP
Input Rating	Non-voltage contact input a) OPEN : 500kW or more b) CLOSE : 10W or less

Analog Output (Optional)
Number of Outputs	1 point / channel
Output Types	a) Measured value (PV) b) Deviation (DV) c) Set value (SV) d) Manipulated output value (MV)
Output Scaling	High limit and Low limit are available.
Output Resolution	13 bits or more
Output Accuracy	0.1% of span
Output Ripple	0.1% of span (When resistive load)

NO	Output Signal	Output Impedance	Allowable Load Resistance
4	0 - 5 V	Less than 0.1W	More than 1kW
6	1 - 5 V	Less than 0.1W	More than 1kW
7	0 - 20mA	Less than 5MW	Less than 600W
8	4 - 20mA	Less than 5MW	Less than 600W

General Specifications
Supply Voltage	a) 85 to 264V AC (Including supply voltage variation) [Rating : 100 to 240V AC] (50/60Hz common) b) 21.6 to 26.4V AC (Including supply voltage variation) [Rating : 24V AC] (50/60Hz common) c) 21.6 to 26.4V DC (Ripple rate 10% p-p or less) [Rating:24VDC]
Power Consumption	Less than 13VA for standard AC type (at 100V AC) Less than 19VA for standard AC type (at 240V AC) Less than 11VA for 24V AC type Less than 340mA for 24V DC type
Power Failure Effect	Not affected by power failure shorter than 20msec, otherwise reset to the initial state.
FAIL Output	a) Check item : MCU trouble, MCU supply voltage trouble, watchdog timer, EEPROM error, input circuit trouble, adjustment error, sensor break b) Output : Relay output, Form A contact 250V AC 1A (resistive load) Abnormal time open.
Operating Environments	0 to 50°C [32 to 122°F] , 45 to 85% RH
Memory Backup	Backed up by non-volatile memory. Number of writing : Approx. 100,000 times
Net Weight	Approx. 530g
External Dimensions	96 x 96 x 100mm (W x H x D)

Compliance with Standards

CE Mark UL Recognized CSA Certified

---

RKC INSTRUMENT INC.